Technological Behavior Parameters of Brazilian Rocks: Insights from the BR-ROCK/10/887 Database

Authors

DOI:

https://doi.org/10.11137/1982-3908_2026_49_72319

Keywords:

Technological characterization, Rock mechanics, Ornamental rocks

Abstract

The study presents a national database on the physical and mechanical properties of Brazilian rocks, compiling information from 888 samples across 168 lithotypes distributed in 22 states. The methodology involved an extensive literature review and the compilation of data into an electronic spreadsheet, covering ten technological parameters (density, porosity, water absorption, uniaxial compressive strength, flexural strength, Amsler wear, hard-body impact, thermal expansion, compressive strength after freeze–thaw cycles, and wave propagation velocity), in addition to identification data. The completeness index reached 65.47%. The results highlight significant differences among lithological groups: metamorphic rocks exhibit higher density and wave velocity, while sedimentary rocks show higher porosity and water absorption, resulting in lower mechanical strength. Igneous and metamorphic rocks display similar behavior, although metamorphic rocks show greater variability in wear and impact resistance. The subdivision by lithotypes emphasizes the high performance of quartzites and volcanic rocks, in contrast to limestones and silicified sandstones. The database provides representative national average values, useful for engineering, geotechnical, and applied geology projects.

Downloads

Download data is not yet available.

Author Biographies

Davi Henrick Veras Diógenes, Universidade Estadual do Ceará

Bachelor’s degree in Geology from the Federal University of Ceará, currently a master’s student in Geomorphology at the State University of Ceará.

Frederico de Holanda Bastos, Universidade Estadual do Ceará

PhD in Geography (Federal University of Ceará/UFC-2012), Master in Sustainable Development (UFC-2005) and Geographer (State University of Ceará/UECE-2000). He is currently a Professor and Researcher in the Department of Geography at UECE, CNPq Research Fellow, Leader of the Research Group "Morphostructure and Morphopedology of Landscapes of Northeastern Brazil" and Coordinator of the Laboratory of Morphostructural and Pedological Studies (LEMEP).

Jordan Elias Barbosa da Silva, Universidade Federal do Ceará

Universidade Federal do Ceará

References

ASTM International 2022a, Standard specification for limestone dimension stone, ASTM C568/C568M-22, ASTM International, West Conshohocken, PA, DOI: 10.1520/C0568_C0568M-22

ASTM International 2022b, Standard specification for quartz-based dimension stone, ASTM C616/C616M-22, ASTM International, West Conshohocken, PA, DOI: 10.1520/C0616_C0616M-22

ASTM International 2022c, Standard specification for slate dimension stone, ASTM C629/C629M-22, ASTM International, West Conshohocken, PA, DOI: 10.1520/C0629_C0629M-22

ASTM International 2023a, Standard specification for granite dimension stone, ASTM C615/C615M-23, ASTM International, West Conshohocken, PA, DOI: 10.1520/C0615_C0615M-23

ASTM International 2023b, Standard specification for marble dimension stone, ASTM C503/C503M-23, ASTM International, West Conshohocken, PA, DOI: 10.1520/C0503_C0503M-23

Barton, N. 1978, ‘Suggested methods for the quantitative description of discontinuities in rock masses: International Society for Rock Mechanics’, International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts, vol. 15, no. 6, pp. 319–368.

Castilho, E.D.F. 2018, Caracterização tecnológica de rochas ornamentais: práticas laboratoriais, Edifes, Vitória, DOI: 10.36524/9788582633144

Cheliz, P.M. & de Oliveira, R.C. 2021, ‘Geomorfologia e estrutura superficial da paisagem de zonas costeiras rochosas: um estudo de caso na Ilha do Cardoso (Litoral Sul de São Paulo)’, Revista Brasileira de Geografia Física, vol. 14, no. 6, pp. 3667–3694, DOI: 10.26848/rbgf.v14.6.p3667-3694

Ching, J. & Phoon, K.K. 2014, ‘Transformations and correlations among some clay parameters — The global database’, Canadian Geotechnical Journal, vol. 51, no. 6, pp. 663–685, DOI: 10.1139/cgj-2013-0262

Ching, J., Li, K., Phoon, K.K. & Weng, M. 2018, ‘Generic transformation models for some intact rock properties’, Canadian Geotechnical Journal, vol. 55, no. 12, pp. 1702–1741, DOI: 10.1139/cgj-2017-0537

Corrêa, F.A., Ribeiro, R.P. & Paraguassú, A.B. 2022, ‘Estudo da alterabilidade de rochas em extrator Soxhlet com novo sistema de condensação sem perda de água’, Anais do XX Congresso Brasileiro de Mecânica dos Solos e Engenharia Geotécnica, Campinas, pp. 4671–4678, DOI: 10.4322/cobramseg.2022.0588

Costa, A.G., Campello, M.S., Maciel, S.L., Calixto, C. & Becerra, J.E. 2002, ‘Rochas ornamentais e de revestimento: proposta de classificação com base na caracterização tecnológica’, Anais do III Simpósio de Rochas Ornamentais do Nordeste, CETEM/MCT, Rio de Janeiro, pp. 55–59, viewed 4 Aug. 2026, http://mineralis.cetem.gov.br/handle/cetem/1434

Deere, D.U. & Miller, R.P. 1966, Engineering classification and index properties for intact rock, Technical Report No. AFWL-TR-65-116, Air Force Weapons Laboratory, Kirtland Air Force Base, NM.

Diógenes, D.H.V. & Clezar Mattos, I. 2025, ‘Geological and industrial characterization of the mylonite belonging to the Granja Complex, Morrinhos - CE’, Anuário do Instituto de Geociências, vol. 48, art. 66134, DOI: 10.11137/1982-3908_2025_48_66134

Eitner, V. & Stölben, F. 2004, ‘International standardisation of ground investigation and testing methods’, in R. Hack, R. Azzam & R. Charlier (eds), Engineering Geology for Infrastructure Planning in Europe, Lecture Notes in Earth Sciences, vol. 104, Springer, Berlin, Heidelberg, pp. 83–91, DOI: 10.1007/978-3-540-39918-6_10

Ferentinou, M. & Muzamhindo, H. 2025, ‘Introduction to ROCK/10/4025 database’, Geodata and AI, vol. 2, art. 100028, DOI: 10.1016/j.geoai.2025.100028

Ferreira, G.C.L., Cattanio, J.H. & Martins, J.G. 2025, ‘Desvendando o potencial da rochagem com pó de rocha granítica de Capitão Poço, no Nordeste Paraense’, Revista Brasileira de Geografia Física, vol. 18, no. 4, pp. 3269–3281, DOI: 10.26848/rbgf.v18.4.p3269-3281

Fontanini, P.S.P., Pimentel, L.L., Jacintho, A.E. & Migliato, C.L. 2012, ‘Brazilian geological sandstone characterization and its utilization as aggregate in structural concrete’, Applied Mechanics and Materials, vol. 271–272, pp. 141–146, DOI: 10.4028/www.scientific.net/AMM.271-272.141

Frazão, E.B. & Farjallat, J.E.S. 1995, ‘Características tecnológicas das principais rochas silicáticas brasileiras usadas como pedras de revestimento’, Anais do I Congresso Internacional da Pedra Natural, Lisboa, pp. 47–58.

Goodman, R.E. 1989, Introduction to Rock Mechanics, 2nd edn, John Wiley & Sons, New York.

Li, P.P., Yu, Q.L., Brouwers, H.J.H. & Chen, W. 2019, ‘Conceptual design and performance evaluation of two-stage ultra-low binder ultra-high performance concrete’, Cement and Concrete Research, vol. 125, art. 105858, DOI: 10.1016/j.cemconres.2019.105858

Palchik, V. 1999, ‘Influence of porosity and elastic modulus on uniaxial compressive strength in soft brittle porous sandstones’, Rock Mechanics and Rock Engineering, vol. 32, no. 4, pp. 303–309, DOI: 10.1007/s006030050050

Pazeto, A., Abiliane, S.A., Faitanin, T.C.B. & Xavier, B. 2020, ‘Estudo comparativo entre propriedades tecnológicas de rochas aglomeradas e rochas naturais: Comparative study between technological properties of agglomerated ans natural stones’, Geociências, vol. 39, no. 4, pp. 1167–1183.

Rickardo, G. & Marcelo, N. 2023, ‘Criteria for specifying rocks in facades’, World Journal of Advanced Research and Reviews, vol. 20, no. 1, pp. 1187–1195, DOI: 10.30574/wjarr.2023.20.1.2176

Shakoor, A. & Bonelli, R.E. 1991, ‘Relationship between petrographic characteristics, engineering index properties, and mechanical properties of selected sandstones’, Bulletin of the Association of Engineering Geologists, vol. 28, no. 1, pp. 55–71, DOI: 10.2113/gseegeosci.xxviii.1.55

Silva, H.V. & Costa, A.G. 2022, ‘Caracterização físico-mecânica de rochas ornamentais do Brasil: determinação de densidade aparente, porosidade, absorção hídrica e capilaridade’, Geociências, vol. 41, no. 3, pp. 769–778, DOI: 10.5016/geociencias.v41i03.16702

Silva, R.R.C., Gonçalves, R. & Bertoldo, C. 2023, ‘Mechanical properties of concrete produced with coarse aggregates from different mineralogical origins using ultrasonic tests’, International Journal of Concrete Structures and Materials, vol. 17, art. 66, DOI: 10.1186/s40069-023-00630-3

Sossai, F.J.M. 2006, Technological characterization of dimension stones, Master’s thesis, Universidade Federal de Viçosa, Viçosa, viewed 4 Aug. 2026, http://locus.ufv.br/handle/123456789/3848

Sun, X., Jiang, M., Miao, C., Zhang, L. & Wang, L. 2025, ‘Creep mechanical properties of sandstones under triaxial compression with different loads and water contents’, Journal of Central South University, vol. 32, pp. 3470–3492, DOI: 10.1007/s11771-025-6078-0

Toscani, S.R.G. & Campos, J.E.G. 2017, ‘Uso de pó de basalto e rocha fosfatada como fertilizante natural em solos lixiviados’, Geociências, vol. 36, no. 2, pp. 259–274

Tuğrul, A. & Zarif, I.H. 1999, ‘Correlation of mineralogical and textural characteristics with engineering properties of selected granitic rocks from Turkey’, Engineering Geology, vol. 51, no. 4, pp. 303–317, DOI: 10.1016/S0013-7952(98)00071-4

Underwood, E.E. 1970, Quantitative Stereology, Addison-Wesley, Reading, MA.

Vidal, F.W.H., Bessa, M.F. & Lima, M.A.B. 1999, Avaliação de rochas ornamentais do Ceará através de suas características tecnológicas, Série Tecnologia Mineral, no. 74, CETEM, Rio de Janeiro.

Zagôto, J.T. 2023, Especificação de rochas ornamentais utilizadas na construção civil aplicando técnicas de estatística multivariada e aprendizado de máquina, Doctoral dissertation, Escola de Minas, Universidade Federal de Ouro Preto, Ouro Preto.

Downloads

Published

2026-11-17

How to Cite

Diógenes, D. H. V., Bastos, F. de H. and Barbosa da Silva, J. E. (2026) “Technological Behavior Parameters of Brazilian Rocks: Insights from the BR-ROCK/10/887 Database”, Anuário do Instituto de Geociências. Rio de Janeiro, BR, 49. doi: 10.11137/1982-3908_2026_49_72319.